Langmeier Backup FAQ

How to avoid five common Langmeier backup mistakes

When setting up backups, there are often small details that are sometimes overlooked. But you should also pay attention to these so that you set up a perfect backup. We will show you some typical mistakes in Langmeier backup setup.

Mistake 1: No backup log by mail

Often people forget to enable emailing for backup logs. Have the backup log emailed to you to get an active notification. Check the log regularly to ensure smooth backup operation. You can enter your email here:

„Options --> Global settings --> Logging --> Email options…“

When setting up backups, there are often small details that are sometimes overlooked. But you should also pay attention to these so that you set up a perfect backup. We'll show you some typical Langmeier backup setup mistakes.

Error 2: Disk is not named - then backup fails because the drive letter changes over time

External hard drives or USB sticks are often named with the drive letter. When removing and inserting different disks, the drive letter of the disk is often changed. However, since the backup is set up on this drive letter, the backup fails with the message that the disk is not available. The solution to this in Langmeier Backup is to name the disk with the name, rather than the drive letter. To do this, specify the name of the volume in the Target Path in the following form:

[volume name]

Concrete example:

Wrong:

When setting up backups, there are often small details that are sometimes overlooked. But you should also pay attention to these so that you set up a perfect backup. We'll show you some typical Langmeier backup setup mistakes.

Right:

When setting up backups, there are often small details that are sometimes overlooked. But you should also pay attention to these so that you set up a perfect backup. We'll show you some typical Langmeier backup setup mistakes.

Mistake 3: There is no media swapping in the companies

The intervals between backups should be adapted to the data flow. A fixed rhythm is good, but it is equally important to set up a media exchange. For this there is also the  „3-2-1 backup rule“.

For a backup it needs at a minimum the so-called 3-2-1 rule, so that a backup is really a backup. The rule goes like this:

  • 3: minimum three copies
  • 2: on a minimum of two different disks
  • 1: One backup kept off-site


Error 4: No administrator user is stored in the service


Suppose you are performing a backup with Langmeier Backup to a network folder and the program behaves like this: manual backups start as desired, but for the automatically set up backup this or a similar error message appears in the log:

Disk \Servername\ShareName\is not available.

Or, if the network folder is the backup source:

Source #1 cannot be found

This is because the Langmeier Backup service runs under the user "System"by default. However, the "System" user has no credentials. It is a credential-less user. However, for security reasons, Windows network shares are often only accessible by a user with credentials. Connections without credentials are thus blocked by Windows.

Solution: Search in the Windows services for the service "Langmeier Backup Service". Right-click on this service and then click "Properties". In the tab "Login" you then store the login data of a user. This user must have permissions on the files and folders to be accessed.

When setting up backups, there are often small details that are sometimes overlooked. But you should also pay attention to these so that you set up a perfect backup. We will show you some typical mistakes during the Langmeier backup setup.

Confirm with OK and restart the service afterwards.

Error 5: Drive shares (e.g. X:\) are used instead of UNC paths with IP address.

Very often it is due to the way the path is written if an automatic backup is not performed. You should not address the devices with the drive letter, but with the UNC notation.

You must  use the UNC notation, which has two backlashes at the beginning:

\XXX.XXX.XXX.XXX\Backup

Concrete example with IP address:

When setting up backups, there are often small details that are sometimes overlooked. But you should also pay attention to these so that you set up a perfect backup. We will show you some typical Langmeier backup setup mistakes.

With a name (= DNS, Domain Name System) it would be like this:Jupiter is an example of the server name here:

When setting up backups, there are often small details that are sometimes overlooked. But you should also pay attention to these so that you set up a perfect backup. We show you some typical mistakes in Langmeier backup setup.

„backup“ must be the share name.

New Version 12

Protect all your files.

Secure 30% discount now!   Buy Now   Try it for free
4
days
4
hours
5
minutes
55
seconds

Langmeier Backup for Windows

About the Author Sebastian Müller
partner support


Sebastian Müller is partner and top customer support at Langmeier Software, making him the best person to talk to about Langmeier backup backup solutions.

Phone: +41 44 861 15 70
Email: sebastian@langmeier-software.com
 

Further lookup: Langmeier Backup, Backup, Data backup, external hard drive, Backup Media, Backup Concept

Articles relevant to the topic
Which backup type is the best choice for my data?
The most frequently asked questions when choosing a backup solution
The pros and cons of the different Windows file systems


Please leave this field blank here:

This article covers:
Langmeier Backup Software